Ayman AYADI

En résumé

Entreprises

• SEREPT - Process Engineer

  Hammam Lif 2009 - maintenant Process Team member ASHTART Offshore Revamp Project:
  - Review and comment process deliverables relevant to the detail design for minor improvements inside SEREPT project team & major improvements within detailed engineering sub-contractors.
  - Review and participate in the preparation of necessary documents for the implementation of Minor work packages: PFDs, PIDs, UFDs, C&E Matrixes, Relief & Blowdown study reports, Calculation notes, Line lists, Tie-in lists, H&M balance reports, simulation reports, Tie-ins installation procedures…
  - Review and comment of process details engineering deliverables relevant to major improvement work packages (Wood Group PSN, RENCO & local engineering contractors).
  - Review and comment: Fire fighting system study report, Blowdown & Flare system design review reports, Fire & gas detection system, C&E Matrixes…
  - Review and participate in the preparation of Tie-ins installation procedures & decommissioning procedures.
  - Review and comment of diesel system improvement and produced water FEED deliverables.
  - Contribute with project disciplines teams in preparation of technical proposal and scope of work.
  - Assistance during kick off and technical clarification meetings of some contracts within the revamping project: such as condensate stabilization column, produced water system, separators…
  - Assist to FAT: Condensate stabilization column, new condensate feed pumps, DCS system.
  - Participate in HAZOP, HAZID & SIL sessions.
  Process Team member ASHTART Production Department:
  - Provide technical support for process engineering activities.
  - Manage and perform process engineering investigations and solutions.
  - Undertake Engineering investigations as to the viability and cost effectiveness of proposed modifications
  - Ensure that the Process Safety in Design is properly addressed and implemented.
  - Take part on the HSSE Audit, Incident Investigation and promote a safety culture within the production department to ensure that all safety issues are reviewed.
  - Coordinate and Communicate information and planning for project in charge: GL compressors fuel gas treatment system overhaul, new PHE implementation & New Diesel centrifugal separator skids.
  - Prepare/Participate on the preparation, monitoring and control the process Engineering budget: OPEX and CAPEX.
  - Prepare/Initiate/Review process Engineering Work packs, prior to MoC approval.
  - Review & verify the design and implementation of modifications in the process disciplines ensuring they meet the appropriate codes and standards.
  - Preparation of technical specifications relating to procurement issues, bids technical evaluation and goods reception such as: IGF, PHE & turbine dual fuel package…
  - Act as the Technical Verification Authority and technical support to site team to process engineering issues in order to maintain asset integrity.
  - Contribute to the creation and update of working procedures and operating manuals facilities.
  - Participate in risk assessment and QA/QC implementation and prepare reports accordingly
  - Review and verify start-up team deliverable such as: Tie-ins installation procedures, Gas-in procedure…, relevant to Major work packages.
  - Review and comment commissioning deliverable such as: System & Sub System List, LTP, OTP…
  - Participate actively on Shut-down preparation: SD SoW, SD philosophy, Site surveys, coordination meetings…
  - Participate in Process Safety workshops: MAH identification, SCS identification, Bowtie Analysis, PS review…
  

• SOTULUB - Chemical-Process Engineer

  2005 - 2009 Chemical-Process engineer in a “used lube oil's” re-refining plant:
  - Participate in the preparation of Process Pre-FEED deliverables for the implementation of a new re-refining plan on Saudi Arabia based on the patented SOTULUB’s used lube oil process: Raw material specifications, Product specifications, Utilities specifications, PFDs, P&IDs, UFDs, Operating manual, Start-up & SD philosophies...
  - Contribute with the revamp & operation teams to the preparation of decommissioning, dismantling, commissioning and start-up procedures.
  - Follow up revamp work & actively participate on decommissioning, commissioning & start-up operations.
  - Updating plant operating manual based on post revamp configuration.
  - Monitor plant production parameters and investigate on production loss and base stocks properties deviations.
  - Contribute to the implementation of an Environmental Management System” ISO 14001”.
  Chemical-Process engineer & Head of R&D and Quality control laboratory since June 2008:
  - Managing a team of 12 technicians & R&D Lead,
  - New lab treatment techniques discovered in order to improve final products stability
  - Preparation of feedstocks Lab analyses reports.
  - Leading & follow-up current MI study and PCB reduction study.
  

Formations

• University Of Gabes, National College Of Engineering - Gabes [ENIG], (Gabès)

  Gabès 2002 - 2005 Master’s Degree: Chemical-Processes Engineering

• University Of Sfax, Preparation Institute For Engineering Studies [IPEIS], (Sfax)

  Sfax 2000 - 2002 BSc Degree Mathematics & Physics

Réseau

• Jasser BOUASKER

• Jean-Marc BERGER

• Mehdi AYADI

• Mohamed GHANNOUCHI

• Omar BOURAOUI

• Yassine GHANDRI