-
SPEC ENERGY (Pvt.) DMCC
- E & I Supervisor & Commissioning.
2015 - maintenant
Assignment for : GAS PLANT EBEDEI.
Project Name : Revamp, Optimize, Commission & Operate Gas Plant.
Project Location : GAS PLANT, EBEDEI DELTA STATE.
Business line : Engineering Procurements, Construction & Pre-comm.
Job Title : E & I Supervisor & Commissioning.
RESPONSIBLE FOR : Construction Upgrade, Inspections, Pre-Comm. & Commissioning
Brief Job Description (Onshore)
Pre-Job Preparation for Electrical and Instrumentation activities / Study job Procedures & specifications to determine appropriate construction methods.
Responsible for the preparation & cross checking of Commissioning & start- up procedure for Commissioning Preparation Team.
Review of pre-commissioning and commissioning dossiers in line with ICAPS and OPERCOM methodology.
Prepare/Coordinate Permit to Work (PTW) for Electrical and Instrumentation related activities.
To oversee the activities of all site teams within my discipline to ensure that all technical, contractual and cost information is properly recorded, collated and available for inspection/reference as required by company policy.
Monitor all E & I related works during prefabrication and erection & Ensure that they are in accordance with the project's design
Overall Field Technical Support for gas Plant electro-mechanical, Piping ,Electrical , Instrumentation installation, Switchgears and Motor Control Centre (MCC) using Technical Drawings,Instrucment Loop Drawings, Control system Design ,System Integration, I/O Layout , including P & ID ,AC/DC Drive Systems ,Power metering equipment & protection ,MCC Panel Layout designs.
Plan, direct, coordinate, through supervisory, personnel activities concerned with the construction and modification of Electrical and Instrumentation installations, facilities, and systems.
Organize E & I activities with Training, coach, allocated resources within the project team and strict monitoring of related progress.
Supervise & Monitor Quality Control activities & Plans within Electrical and Instrumentation installations.
E & I Requisition supplies and materials to complete GAS PLANT projects.
Identify deficiencies and develop solutions to identified construction problems within my discipline.
Review and comment site queries related to E & I works and co-ordinate the response with Electrical leader.
Maintain effective communication with all Daily reporting to Electrical Leader.
Provide information on modification on work policies, safety regulations, Electrical & Instrument codes, Standards and specifications.
Support in Reviewing Electrical & Instrument Engineering Team in design needs /Changes on Site.
To ensure that all construction activities related to E & I are performed safely and efficiently in line with company objectives.
Supervise site pre-commissioning and Start-up commissioning phases for those aspects related to the gas plants Revamping, Optimizing & Operation process for supply.
Attend Daily toolbox meetings.
Stay vigilant and maintain continuous HSE awareness/Culture of hazards & surroundings.
Participate on site programs or initiatives to improve HSE performances.
Witness and inspect all Electrical & Instrument New Materials, Equipment's before Installations.
PUNCH List Preparation, checked and close out
Field/Site Installation Supervision, Testing (Pre-commissioning & Commissioning Activities):
Marshalling Cabinet
MCC Units/Panel
Electrical Switchgears (HV & LV)
E & I Cable Trays (Sizes: 50mm, 100mm, 200mm etc.)
I & C Cable Installations (Sizes :)
Electrical Cables Installations (Sizes :)
Primary Supports fabrications for E & I
Valves: ESDV, SDV, PSV, Control Valves & Testing, Calibration, SAT.
Electronic and Pneumatic Transmitter.
(Pressure, Level, Temperature, Flow)
Earthing Cables ,Bus bars ,Earthing grids & Testing
Gas Lift Systems.
Fire & Gas Alarm Systems.
LV & HV Circuit Breakers.
E & I Junction boxes / Panels.
Safety security systems (EPB etc.)
Field Instrument (Gas & Smoke Detectors )
Electric Motors & Testing (Sizes :)
Cathodic Protection Systems (MMO Ribbon & Sacrificial Anode), Testing etc.
-
SPEC ENERGY (Pvt.) DMCC
- E & I Supervisor & Commissioning.
2015 - maintenant
Assignment for : GAS PLANT EBEDEI.
Project Name : Revamp, Optimize, Commission & Operate Gas Plant.
Project Location : GAS PLANT, EBEDEI DELTA STATE.
Business line : Engineering Procurements, Construction & Pre-comm.
Job Title : E & I Supervisor & Commissioning.
RESPONSIBLE FOR : Construction Upgrade, Inspections, Pre-Comm. & Commissioning
Brief Job Description (Onshore)
Pre-Job Preparation for Electrical and Instrumentation activities / Study job Procedures & specifications to determine appropriate construction methods.
Responsible for the preparation & cross checking of Commissioning & start- up procedure for Commissioning Preparation Team.
Review of pre-commissioning and commissioning dossiers in line with ICAPS and OPERCOM methodology.
Prepare/Coordinate Permit to Work (PTW) for Electrical and Instrumentation related activities.
To oversee the activities of all site teams within my discipline to ensure that all technical, contractual and cost information is properly recorded, collated and available for inspection/reference as required by company policy.
Monitor all E & I related works during prefabrication and erection & Ensure that they are in accordance with the project's design
Overall Field Technical Support for gas Plant electro-mechanical, Piping ,Electrical , Instrumentation installation, Switchgears and Motor Control Centre (MCC) using Technical Drawings,Instrucment Loop Drawings, Control system Design ,System Integration, I/O Layout , including P & ID ,AC/DC Drive Systems ,Power metering equipment & protection ,MCC Panel Layout designs.
Plan, direct, coordinate, through supervisory, personnel activities concerned with the construction and modification of Electrical and Instrumentation installations, facilities, and systems.
Organize E & I activities with Training, coach, allocated resources within the project team and strict monitoring of related progress.
Supervise & Monitor Quality Control activities & Plans within Electrical and Instrumentation installations.
E & I Requisition supplies and materials to complete GAS PLANT projects.
Identify deficiencies and develop solutions to identified construction problems within my discipline.
Review and comment site queries related to E & I works and co-ordinate the response with Electrical leader.
Maintain effective communication with all Daily reporting to Electrical Leader.
Provide information on modification on work policies, safety regulations, Electrical & Instrument codes, Standards and specifications.
Support in Reviewing Electrical & Instrument Engineering Team in design needs /Changes on Site.
To ensure that all construction activities related to E & I are performed safely and efficiently in line with company objectives.
Supervise site pre-commissioning and Start-up commissioning phases for those aspects related to the gas plants Revamping, Optimizing & Operation process for supply.
Attend Daily toolbox meetings.
Stay vigilant and maintain continuous HSE awareness/Culture of hazards & surroundings.
Participate on site programs or initiatives to improve HSE performances.
Witness and inspect all Electrical & Instrument New Materials, Equipment's before Installations.
PUNCH List Preparation, checked and close out
Field/Site Installation Supervision, Testing (Pre-commissioning & Commissioning Activities):
Marshalling Cabinet
MCC Units/Panel
Electrical Switchgears (HV & LV)
E & I Cable Trays (Sizes: 50mm, 100mm, 200mm etc.)
I & C Cable Installations (Sizes :)
Electrical Cables Installations (Sizes :)
Primary Supports fabrications for E & I
Valves: ESDV, SDV, PSV, Control Valves & Testing, Calibration, SAT.
Electronic and Pneumatic Transmitter.
(Pressure, Level, Temperature, Flow)
Earthing Cables ,Bus bars ,Earthing grids & Testing
Gas Lift Systems.
Fire & Gas Alarm Systems.
LV & HV Circuit Breakers.
E & I Junction boxes / Panels.
Safety security systems (EPB etc.)
Field Instrument (Gas & Smoke Detectors )
Electric Motors & Testing (Sizes :)
Cathodic Protection Systems (MMO Ribbon & Sacrificial Anode), Testing etc.
-
SNEF NIGERIA SERVICES
- QAQC Manager
2013 - 2015
Assignment for : TOTAL E & P/PONTICELLI NIGERIA LIMITED
Project Name : OFON, AMENAM OKPONO EPCI5 Phase 2 Project.
Project Location : PNL YARD & GULF OF GUINEA.
Business line : Engineering Procurements, Construction & Pre-comm.
Job Title : QAQC Manager E & I
RESPONSIBLE FOR : Construction, Inspections, ICAPS Turnover, Pre-Comm & Commissioning
Brief Job Description (Onshore)
Projects quality control documents preparation & reviews - Inspection Test Plans, Work Procedures, Request for Inspections form, and method statements for contractor & Company.
Co-ordinate & manage with SPIE NIG LTD on Issues related to Dossiers ,ICAP's ,Total - OPERCOM, Vendor Documents, Vendor Inspections , Site deviation/Mark -Up etc.
Prepare the initial project Qa/Qc plans for the initial submittal for Company approval.
Participate actively in the continued development and improvement of QMS system.
Carry out internal audits with Contractor for Projects documents, material/equipment vendors, verifying the company's adherence to the Qa/Qc sections of QMS.
Co-ordinate and follow up with Auditee's to establish if corrective and preventive actions are being implemented and maintained.
Lead development and implementation of project procurement, support engineering, construction planning and fabrication in accordance with Qa/Qc program, systems and processes.
Recruit suitably qualified personnel & Recommend initial training, evaluation & maintain detailed records of all Qa/Qc personnel.
Attend all necessary meetings as required.
Witness and inspect all Electrical, Instrument & Telecomm Supports during Fabrication, Blasting and Painting.
Prepare Yard RFI for Company Inspections of Supports Ready for Offshore Installations.
Witness and inspect all Electrical, Instrument & Telecomm New Materials, Equipment's Using MRI Record.
VALVES _Calibration & Acceptance Test
GIL Automation (Potent Global World Limited_trans-amadi, PH).
Pressure safety valves ,Pilot Valves
FAT _Factory Acceptance Test
Cameron west Africa Ltd_Oil & Gas free zone, FLT Onne Nigeria.
Cameron Valves & Measurement & BV,
Valve & Actuator Assembling, Blasting and Painting with Test.
Valve & Actuator inspections, hydrostatic shell & Gas testing (HP & LP).
Brief Job Description (Offshore)
Co-ordinate in the final preparation of completed quality control inspections & ICAP's Sheets for Electrical, Instrument & Telecomm after pre-commissioning & Commissioning activities in dossiers for SPIE NIG LTD & TOTAL E & P.
Co-ordinate with projects & Construction manager to ensure the projects are adequately manned with Qa/Qc, E & I personnel's.
Communicate regularly with the projects & Construction manager insure or reports generated in the Qa/Qc department as pertaining to the project construction for actions.
Assist and advice wherever necessary in relation to the Qa/Qc implementation including the closure of NCR's IN's, CAR's & PQI, maintain overall projects logs & records.
Provide support and guidance for all Qa/Qc staff in relation to the execution of their duties.
Prepare and issue monthly reports and issue to head office and project representative on the projects.
Monitor with necessary Projects Planning of all Electrical, Instrument & Telecomm installations by construction team; testing and QC inspections activities by the inspectors on the platform and make sure inspection reports and quality plan are maintained at the end of the inspections/pre-commissioning.
Follow up inspections and maintain records of all in & out E, I & Telecom materials on the platform.
Regular site/platform daily, weekly and monthly meetings for the progress of the projects Target.
Ensures, whenever necessary, the update of site projects drawings/platform Qc Plans/Control Procedures, directing all deviations/Change to the Project Quality Engineers/Engineering.
Maintain all projects EHS or HSE requirements - PPE, Work permit, stop work culture if not safe and promote the use of HSE practices.
FIELD E & I, T Installations Supervision, Pre-commissioning & Commissioning
Quality control & pre-commissioning & Commissioning activities with AFC Drawings (TSLD, Hook-up, wiring drawing & details, P&ID drawings, schematic & location drawings, New mark-ups on projects & vendor drawings).
ICSS Systems - cables & cabinets Installations and Tie in.
FGS, PSS and PCS cabinet internal loop modification and wiring.
Loop test with associated safety functions.
Electrical motor installations (400v & above).
Electrical panel installation & modification (230v ~400v)
Cable installations (500v~1000v & Above cable voltage ratings)
6.6KV CELL Switchgear installations to link existing bus section.
SWITCHGEAR & MCC Upgrade at Electrical Room.
PAGA Systems : cables, JB's, loudspeakers (indoor & outdoor) installations.
CCTV System : cables, JB's, panels, CCTV device.
Fabricated supports for E, I & T installations (Welding, Blasting & Panel).
Cable trays for LV, MV & control cables Installations.
LV & HV Cables for new Transformers after Installations.
Valves installation & testing _SDV, ESDV, PSV & Control valves.
Tubing lines & Manifolds installations on Skids, wellheads, Control panels, Instruments & Leak test on tubing to instruments & manifolds etc.
MCT's Installations for Cables routing on platforms.
Earthing system installations _Cabinets, JB's, instruments, skids, control panels, cable trays, supports etc.
Circuit breakers, Relays, thermostat, fuse, MCB's installation.
Telecommunication fibre cables installations & test inspections.
Fire and Gas Alarm Systems.
PUNCH List Preparation, checked and close out.
Installation & Testing of Equipment's including:
Marshaling Cabinet SSS, PCS.
Wellhead Control Panels.
Electronic and Pneumatic Transmitter.
(Pressure, Level, Temperature, Flow)
Deluge System.
FM200
Gas Lift System
Gas Detector System etc.
-
SNEF NIGERIA SERVICES
- QAQC Manager
2013 - 2015
Assignment for : TOTAL E & P/PONTICELLI NIGERIA LIMITED
Project Name : OFON, AMENAM OKPONO EPCI5 Phase 2 Project.
Project Location : PNL YARD & GULF OF GUINEA.
Business line : Engineering Procurements, Construction & Pre-comm.
Job Title : QAQC Manager E & I
RESPONSIBLE FOR : Construction, Inspections, ICAPS Turnover, Pre-Comm & Commissioning
Brief Job Description (Onshore)
Projects quality control documents preparation & reviews - Inspection Test Plans, Work Procedures, Request for Inspections form, and method statements for contractor & Company.
Co-ordinate & manage with SPIE NIG LTD on Issues related to Dossiers ,ICAP's ,Total - OPERCOM, Vendor Documents, Vendor Inspections , Site deviation/Mark -Up etc.
Prepare the initial project Qa/Qc plans for the initial submittal for Company approval.
Participate actively in the continued development and improvement of QMS system.
Carry out internal audits with Contractor for Projects documents, material/equipment vendors, verifying the company's adherence to the Qa/Qc sections of QMS.
Co-ordinate and follow up with Auditee's to establish if corrective and preventive actions are being implemented and maintained.
Lead development and implementation of project procurement, support engineering, construction planning and fabrication in accordance with Qa/Qc program, systems and processes.
Recruit suitably qualified personnel & Recommend initial training, evaluation & maintain detailed records of all Qa/Qc personnel.
Attend all necessary meetings as required.
Witness and inspect all Electrical, Instrument & Telecomm Supports during Fabrication, Blasting and Painting.
Prepare Yard RFI for Company Inspections of Supports Ready for Offshore Installations.
Witness and inspect all Electrical, Instrument & Telecomm New Materials, Equipment's Using MRI Record.
VALVES _Calibration & Acceptance Test
GIL Automation (Potent Global World Limited_trans-amadi, PH).
Pressure safety valves ,Pilot Valves
FAT _Factory Acceptance Test
Cameron west Africa Ltd_Oil & Gas free zone, FLT Onne Nigeria.
Cameron Valves & Measurement & BV,
Valve & Actuator Assembling, Blasting and Painting with Test.
Valve & Actuator inspections, hydrostatic shell & Gas testing (HP & LP).
Brief Job Description (Offshore)
Co-ordinate in the final preparation of completed quality control inspections & ICAP's Sheets for Electrical, Instrument & Telecomm after pre-commissioning & Commissioning activities in dossiers for SPIE NIG LTD & TOTAL E & P.
Co-ordinate with projects & Construction manager to ensure the projects are adequately manned with Qa/Qc, E & I personnel's.
Communicate regularly with the projects & Construction manager insure or reports generated in the Qa/Qc department as pertaining to the project construction for actions.
Assist and advice wherever necessary in relation to the Qa/Qc implementation including the closure of NCR's IN's, CAR's & PQI, maintain overall projects logs & records.
Provide support and guidance for all Qa/Qc staff in relation to the execution of their duties.
Prepare and issue monthly reports and issue to head office and project representative on the projects.
Monitor with necessary Projects Planning of all Electrical, Instrument & Telecomm installations by construction team; testing and QC inspections activities by the inspectors on the platform and make sure inspection reports and quality plan are maintained at the end of the inspections/pre-commissioning.
Follow up inspections and maintain records of all in & out E, I & Telecom materials on the platform.
Regular site/platform daily, weekly and monthly meetings for the progress of the projects Target.
Ensures, whenever necessary, the update of site projects drawings/platform Qc Plans/Control Procedures, directing all deviations/Change to the Project Quality Engineers/Engineering.
Maintain all projects EHS or HSE requirements - PPE, Work permit, stop work culture if not safe and promote the use of HSE practices.
FIELD E & I, T Installations Supervision, Pre-commissioning & Commissioning
Quality control & pre-commissioning & Commissioning activities with AFC Drawings (TSLD, Hook-up, wiring drawing & details, P&ID drawings, schematic & location drawings, New mark-ups on projects & vendor drawings).
ICSS Systems - cables & cabinets Installations and Tie in.
FGS, PSS and PCS cabinet internal loop modification and wiring.
Loop test with associated safety functions.
Electrical motor installations (400v & above).
Electrical panel installation & modification (230v ~400v)
Cable installations (500v~1000v & Above cable voltage ratings)
6.6KV CELL Switchgear installations to link existing bus section.
SWITCHGEAR & MCC Upgrade at Electrical Room.
PAGA Systems : cables, JB's, loudspeakers (indoor & outdoor) installations.
CCTV System : cables, JB's, panels, CCTV device.
Fabricated supports for E, I & T installations (Welding, Blasting & Panel).
Cable trays for LV, MV & control cables Installations.
LV & HV Cables for new Transformers after Installations.
Valves installation & testing _SDV, ESDV, PSV & Control valves.
Tubing lines & Manifolds installations on Skids, wellheads, Control panels, Instruments & Leak test on tubing to instruments & manifolds etc.
MCT's Installations for Cables routing on platforms.
Earthing system installations _Cabinets, JB's, instruments, skids, control panels, cable trays, supports etc.
Circuit breakers, Relays, thermostat, fuse, MCB's installation.
Telecommunication fibre cables installations & test inspections.
Fire and Gas Alarm Systems.
PUNCH List Preparation, checked and close out.
Installation & Testing of Equipment's including:
Marshaling Cabinet SSS, PCS.
Wellhead Control Panels.
Electronic and Pneumatic Transmitter.
(Pressure, Level, Temperature, Flow)
Deluge System.
FM200
Gas Lift System
Gas Detector System etc.
-
SPIE OIL & GAS SERVICES
- Sr. E & I Commissioning Engineer
2013 - 2013
Assignment for : TOTAL E & P Downstream.
Project Name : OML 58.
Project Location : OBAGI, RIVERS STATE, NIGERIA
Business line : EPC, Pre-commissioning & Commissioning
Job Title : Sr. E & I Commissioning Engineer.
RESPONSIBLE FOR : Constructions, Inspections, ICAP's, Pre-commissioning & Comm.
Brief Job Description (Onshore)
Responsible for the preparation & cross checking of Commissioning & start- up procedure for Commissioning Preparation Team.
Review of pre-commissioning and commissioning dossiers in line with ICAPS and OPERCOM methodology.
Site visual verification of system ready for Commissioning & start-up Perform technical tasks assigned by Project Commissioning Leader, related to the preparation of the commissioning and start up activities.
In charge to manage, supervise and co-ordinate EPC (Interface with engineering disciplines, licensors, vendors and subcontractor) to accomplish Pre-commissioning & Commissioning phase and to raise RFC Dossier for subsystems and systems.
Performing Pre-commissioning, Commissioning activity on all Electrical equipment from 415 volts to 33 kV, 6.6 kV Power System and preparing to Plant Start-Up stage.
Testing of all types of Integrated Protective Relays and associated components of HV/MV/LV Switchgears, MCC, GIS, VFD and Generators.
Commissioning of different Electrical Equipment's such as CTs, PTs, Circuit Breakers, Isolators, Protection Relays, overall scheme checking, Cable Schedule preparation and as-build drawing preparation for 33/3.3 kV, 3.3/0.415 kV Substation and its associates.
Performing Pre-commissioning & Commissioning activities associated with Tri-Ethylene Glycol Booster, Circulation, Handling & Re-Generation Packages, Water Disposal, Vapor Recovery & Booster Packages, Chemical Injection, Corrosion Inhibitor & Methanol Packages, Fin Fan, After Cooler systems, Flare Knock-Out (KO) Drum system, Closed/Open, Process Drain System, Oil/Gas Lifting Packages, Instrument Air, Produced Water packages, HVAC and Utilities etc...
Pre-commissioning, Commissioning activity of control, protection circuits & relay interposing panel for LV Motor, Transformer, Bus Coupler, Normal Feeder, Emergency Feeder, power control centre and Motor Control Centre, Emergency Diesel Generator etc...
Prepared Test Report and `As built cable schedule', `As Built Single line, interconnection & schematic drawing' for process plant.
Pre-commissioning, Commissioning of Transformer protection, Transformer Differential Protection & REF Protection, Bus Bar protection, Motor protection, and synchronizing scheme, complete checks, updated the circuit diagrams with red corrections, Mechanical completion reports and submission to the concerned authority.
Commissioning and Start-UP activities of 6.6 kV Panel, LV Power distribution board, UPS, Power Management System, Well Head Control System, Flash Gas Compression system, Flash gas Compressor package, Glycol Handling/Regeneration system, Air Compressor, Super Heater, Lube Oil Cooler system, HVAC, Safety and Firefighting equipment system, Anti-Corrosions system, De-min/Produced water system, Crane, Nav-Aids system Closed/Open Drain system DCS, ESD, F&G at hazardous environment with in gas and power facilities.
Executed Transformer Test and function test with stability checks (Differential, Restricted & standby earth fault protections). LT Motors test, Protective relays and Scheme test with stability check (differential protection). Generator Test and scheme test with stability checks (Differential & Earth fault protection). Switch yard power transformer and electrical equipment's testing and commissioning. Numerical and electro mechanical relays testing and commissioning for power transformer, Generator, motor, incoming and outgoing feeders.
Insulation Resistance Test and HIPOT Test for HV, Submergible cables, Meggering at 5000V and HI-POT test at 30KV, prepared the Cables and conduct Continuity Test, Insulation Resistance Test for its reliability.
Prepared the Motors and its associated Equipment's like LCS, Emergency Stopper, Space Heaters, Feeder and conducted Winding Resistance, Winding Insulation Resistance, Protection Relay settings, Functional Test, Direction of Rotor, No Load Test, Mechanical Load Test etc...
Prepared the Relay and performed Secondary Injection Test to ensure the under current, Over voltage, Earth fault, over current, thermal protections against real time faults.
Electrical Substations 34,8KV/13,4KV/4.16KV/480V with Fire Alarm System, FM 200 Extinguishment System, HVAC System, UPS System, Battery Chargers, Cathodic Protection, Heat Tracing, Lighting System, Earthing System.
Polarity test.
Leak test on impulse line.
Earth fault loop impedance test.
Earth electrode resistance test.
Continuity test of protective conductors & Ring final circuit.
Prepared operational test procedures on fire water system, including ESD system using cause and effect matrix, Troubleshooting of field sensors, instruments, control system cards and perform system modifications and generate new loop drawing performing trending in DCS.
Loop checking field instrument ( Pressure transmitter, Temperature transmitter, Flow transmitter, Level transmitter, Temperature element, Gas detector transmitter, Flame detector transmitter, pressure differential transmitter, Guided wave interface and radar level transmitter , Pressure switch, Level switch, Temperature switch, Flow switch, Pneumatic control valve with positioner, Solenoid and Motor operated control valve, Thermal detector ).
E & I PUNCH List item checked & close out.
Maintain all projects EHS or HSE requirements (SIMOP) - PPE, Work permit, stop work culture if not safe and promote the use of HSE practices.
-
SPIE OIL & GAS SERVICES
- Sr. E & I Commissioning Engineer
2013 - 2013
Assignment for : TOTAL E & P Downstream.
Project Name : OML 58.
Project Location : OBAGI, RIVERS STATE, NIGERIA
Business line : EPC, Pre-commissioning & Commissioning
Job Title : Sr. E & I Commissioning Engineer.
RESPONSIBLE FOR : Constructions, Inspections, ICAP's, Pre-commissioning & Comm.
Brief Job Description (Onshore)
Responsible for the preparation & cross checking of Commissioning & start- up procedure for Commissioning Preparation Team.
Review of pre-commissioning and commissioning dossiers in line with ICAPS and OPERCOM methodology.
Site visual verification of system ready for Commissioning & start-up Perform technical tasks assigned by Project Commissioning Leader, related to the preparation of the commissioning and start up activities.
In charge to manage, supervise and co-ordinate EPC (Interface with engineering disciplines, licensors, vendors and subcontractor) to accomplish Pre-commissioning & Commissioning phase and to raise RFC Dossier for subsystems and systems.
Performing Pre-commissioning, Commissioning activity on all Electrical equipment from 415 volts to 33 kV, 6.6 kV Power System and preparing to Plant Start-Up stage.
Testing of all types of Integrated Protective Relays and associated components of HV/MV/LV Switchgears, MCC, GIS, VFD and Generators.
Commissioning of different Electrical Equipment's such as CTs, PTs, Circuit Breakers, Isolators, Protection Relays, overall scheme checking, Cable Schedule preparation and as-build drawing preparation for 33/3.3 kV, 3.3/0.415 kV Substation and its associates.
Performing Pre-commissioning & Commissioning activities associated with Tri-Ethylene Glycol Booster, Circulation, Handling & Re-Generation Packages, Water Disposal, Vapor Recovery & Booster Packages, Chemical Injection, Corrosion Inhibitor & Methanol Packages, Fin Fan, After Cooler systems, Flare Knock-Out (KO) Drum system, Closed/Open, Process Drain System, Oil/Gas Lifting Packages, Instrument Air, Produced Water packages, HVAC and Utilities etc...
Pre-commissioning, Commissioning activity of control, protection circuits & relay interposing panel for LV Motor, Transformer, Bus Coupler, Normal Feeder, Emergency Feeder, power control centre and Motor Control Centre, Emergency Diesel Generator etc...
Prepared Test Report and `As built cable schedule', `As Built Single line, interconnection & schematic drawing' for process plant.
Pre-commissioning, Commissioning of Transformer protection, Transformer Differential Protection & REF Protection, Bus Bar protection, Motor protection, and synchronizing scheme, complete checks, updated the circuit diagrams with red corrections, Mechanical completion reports and submission to the concerned authority.
Commissioning and Start-UP activities of 6.6 kV Panel, LV Power distribution board, UPS, Power Management System, Well Head Control System, Flash Gas Compression system, Flash gas Compressor package, Glycol Handling/Regeneration system, Air Compressor, Super Heater, Lube Oil Cooler system, HVAC, Safety and Firefighting equipment system, Anti-Corrosions system, De-min/Produced water system, Crane, Nav-Aids system Closed/Open Drain system DCS, ESD, F&G at hazardous environment with in gas and power facilities.
Executed Transformer Test and function test with stability checks (Differential, Restricted & standby earth fault protections). LT Motors test, Protective relays and Scheme test with stability check (differential protection). Generator Test and scheme test with stability checks (Differential & Earth fault protection). Switch yard power transformer and electrical equipment's testing and commissioning. Numerical and electro mechanical relays testing and commissioning for power transformer, Generator, motor, incoming and outgoing feeders.
Insulation Resistance Test and HIPOT Test for HV, Submergible cables, Meggering at 5000V and HI-POT test at 30KV, prepared the Cables and conduct Continuity Test, Insulation Resistance Test for its reliability.
Prepared the Motors and its associated Equipment's like LCS, Emergency Stopper, Space Heaters, Feeder and conducted Winding Resistance, Winding Insulation Resistance, Protection Relay settings, Functional Test, Direction of Rotor, No Load Test, Mechanical Load Test etc...
Prepared the Relay and performed Secondary Injection Test to ensure the under current, Over voltage, Earth fault, over current, thermal protections against real time faults.
Electrical Substations 34,8KV/13,4KV/4.16KV/480V with Fire Alarm System, FM 200 Extinguishment System, HVAC System, UPS System, Battery Chargers, Cathodic Protection, Heat Tracing, Lighting System, Earthing System.
Polarity test.
Leak test on impulse line.
Earth fault loop impedance test.
Earth electrode resistance test.
Continuity test of protective conductors & Ring final circuit.
Prepared operational test procedures on fire water system, including ESD system using cause and effect matrix, Troubleshooting of field sensors, instruments, control system cards and perform system modifications and generate new loop drawing performing trending in DCS.
Loop checking field instrument ( Pressure transmitter, Temperature transmitter, Flow transmitter, Level transmitter, Temperature element, Gas detector transmitter, Flame detector transmitter, pressure differential transmitter, Guided wave interface and radar level transmitter , Pressure switch, Level switch, Temperature switch, Flow switch, Pneumatic control valve with positioner, Solenoid and Motor operated control valve, Thermal detector ).
E & I PUNCH List item checked & close out.
Maintain all projects EHS or HSE requirements (SIMOP) - PPE, Work permit, stop work culture if not safe and promote the use of HSE practices.
-
SNEF
- QAQC Mgr
2013 - 2015
-
DAEWOO E&C
- QAQC Engineer E & I
2008 - 2013
Assignment for : CHEVRON NIGERIA LIMITED/KBR (SGC)
Project Name : GAS TO LIQUIDS Project 1
Project Location : ESCRAVOS, NIGERIA
Business line : Engineering Procurements, Construction & Pre-comm.
Job Title : QAQC Engineer E & I
RESPONSIBLE FOR : Constructions, Inspections, TOSTR, Pre-commissioning & Commissioning
Brief Job Description (Onshore)
Professional ability for Turnover System Tracking Report (TOSTR), Handing over Completed inspected jobs quality forms to contractor/company.
Daily, weekly and monthly meetings with Clients (Chevron Nigeria Limited, Local companies and vendors, also participate in sectional & department progress meetings.
Lead development and implementation of project procurement, support engineering, construction planning and fabrication in accordance with quality assurance and control program, systems and processes.
Establish and manage sub-contractor, vendor performance against QA/QC requirements and act on results to assure necessary corrective measures are implemented.
Develop and maintain positive working relationship with Company and contractor staff.
Assure accurate quality assurance programs, processes and timely data collection for reporting.
Checking & Inspection using Working Procedures With Specifications, Inspection & Test Plan, Quality forms/sheets for all related work on the client site/projects ( Chevron Nigeria Limited ).
Equipment's-Welding Machines Calibration before use on the EGTL1 Projects site.
Projects Inspections Documents Reviews - Inspection Test Plans, Work Procedures, Request for Inspections, method statement.
Carry out quality control functions / activities of the projects or its parts, Including quality control inspection schedules & collection of quality control records; ensuring the availability quality records documents and implementation of quality plan on site.
Maintain daily test, controls & inspections are carried out inspections on electrical and instrument installations& that personnel have access to all required projects documentation on site.
Ensures, whenever necessary, the update of Site Quality Control Plans/Control Procedures, directing all Deviations Regarding the Contract to the Project Quality Engineers.
Co-operates in event report management & for all the implementation of relative actions, systematically record the Non-Conformity of the events reports issued & identify proper Corrective Actions.
Ensure the preparation of construction document in the defined Engineering System giving the correct priority & sequences, in accordance with defined plans & consistent with the Contracture Schedule.
Management experience in establishment, operation & maintenance of a QMS in accordance with ISO 9001 or equivalent with the capacity of developing quality system, quality plans, work procedures & inspection plans.
FIELD E & I, T Installations Supervision, Testing (Pre-commissioning & Commissioning):
Preservation of LV & MV Switchgears, HVAC on Substations Controls, Electrical Motors.
Installation inspection of Telephone systems, Panic alarm systems, Fire and gas systems, Intrusion detection systems, Access control system, CCTV camera systems.
Inspection of lighting systems & fixtures, DB & panels, receptacles, cable trays, grounding & rods, lightning protection systems, Transformers & bus duct, etc.
Installation of Reactor valve tray.
Routine calibration welding machines and instrument devices.
Involvement in functional checks and tests for electrical & Instruments system energization and commissioning.
Prepare electric substation layout arrangement, interconnecting wiring diagrams, checks and review electrical cable lay down documentation and electrical network layout documentation (grounding, lighting, cathode protection, electric heat tracing and connection boxes).
Inspection Cathodic protection System on tanks & tank bottom, underground & above pipes for drains & gas lines, deep well ground beds, underground cathodic protection cables, main and negative JB, transformer rectifier system.
Inspection of MFOC & PA/GA Instrument Panel, Cables (Secondary & primary cables), Fiber optic cable, wiring test , Instrument JB & Control panel, Instrument cable tray, Instrument air , leak testing, Instrument Loop check ,transmitters ,Indicators ,Analyzers ,local controller ,temperature gauge ,pressure gauge ,safety valve ,thermocouple , hand switch , pressure switch ,solenoid valve, control valve ,valve positioner , gas & smoke detectors, PSV & PRV, On-off valves installations, Non-displacer level etc.
Inspection Steam tracing on MANIFOLDS ,pressure insulated tube, vessels & pipes, material identification, receiving & storage , Pipe preparation, surface cleaning on location of installations, piping projections, thermo & angle of tubing ,steam tracer tubing piping & steam traps, steam tracing tubing & insulation, steam tracing panel (Tranter panel coils& Heat transfer compound)
E & I PUNCH List item checked & close out.
Pre-Commissioning & Commissioning with vendor site representative and project operations team for completed works/jobs, participated on all work down, functional check , test prior to energizing and start-up in substations, Skids & Modules, electrical panels, MCC & switchgears, Bar-bus units, Battery bank system etc.
-
DAEWOO E&C
- QAQC Engineer E & I
2008 - 2013
Assignment for : CHEVRON NIGERIA LIMITED/KBR (SGC)
Project Name : GAS TO LIQUIDS Project 1
Project Location : ESCRAVOS, NIGERIA
Business line : Engineering Procurements, Construction & Pre-comm.
Job Title : QAQC Engineer E & I
RESPONSIBLE FOR : Constructions, Inspections, TOSTR, Pre-commissioning & Commissioning
Brief Job Description (Onshore)
Professional ability for Turnover System Tracking Report (TOSTR), Handing over Completed inspected jobs quality forms to contractor/company.
Daily, weekly and monthly meetings with Clients (Chevron Nigeria Limited, Local companies and vendors, also participate in sectional & department progress meetings.
Lead development and implementation of project procurement, support engineering, construction planning and fabrication in accordance with quality assurance and control program, systems and processes.
Establish and manage sub-contractor, vendor performance against QA/QC requirements and act on results to assure necessary corrective measures are implemented.
Develop and maintain positive working relationship with Company and contractor staff.
Assure accurate quality assurance programs, processes and timely data collection for reporting.
Checking & Inspection using Working Procedures With Specifications, Inspection & Test Plan, Quality forms/sheets for all related work on the client site/projects ( Chevron Nigeria Limited ).
Equipment's-Welding Machines Calibration before use on the EGTL1 Projects site.
Projects Inspections Documents Reviews - Inspection Test Plans, Work Procedures, Request for Inspections, method statement.
Carry out quality control functions / activities of the projects or its parts, Including quality control inspection schedules & collection of quality control records; ensuring the availability quality records documents and implementation of quality plan on site.
Maintain daily test, controls & inspections are carried out inspections on electrical and instrument installations& that personnel have access to all required projects documentation on site.
Ensures, whenever necessary, the update of Site Quality Control Plans/Control Procedures, directing all Deviations Regarding the Contract to the Project Quality Engineers.
Co-operates in event report management & for all the implementation of relative actions, systematically record the Non-Conformity of the events reports issued & identify proper Corrective Actions.
Ensure the preparation of construction document in the defined Engineering System giving the correct priority & sequences, in accordance with defined plans & consistent with the Contracture Schedule.
Management experience in establishment, operation & maintenance of a QMS in accordance with ISO 9001 or equivalent with the capacity of developing quality system, quality plans, work procedures & inspection plans.
FIELD E & I, T Installations Supervision, Testing (Pre-commissioning & Commissioning):
Preservation of LV & MV Switchgears, HVAC on Substations Controls, Electrical Motors.
Installation inspection of Telephone systems, Panic alarm systems, Fire and gas systems, Intrusion detection systems, Access control system, CCTV camera systems.
Inspection of lighting systems & fixtures, DB & panels, receptacles, cable trays, grounding & rods, lightning protection systems, Transformers & bus duct, etc.
Installation of Reactor valve tray.
Routine calibration welding machines and instrument devices.
Involvement in functional checks and tests for electrical & Instruments system energization and commissioning.
Prepare electric substation layout arrangement, interconnecting wiring diagrams, checks and review electrical cable lay down documentation and electrical network layout documentation (grounding, lighting, cathode protection, electric heat tracing and connection boxes).
Inspection Cathodic protection System on tanks & tank bottom, underground & above pipes for drains & gas lines, deep well ground beds, underground cathodic protection cables, main and negative JB, transformer rectifier system.
Inspection of MFOC & PA/GA Instrument Panel, Cables (Secondary & primary cables), Fiber optic cable, wiring test , Instrument JB & Control panel, Instrument cable tray, Instrument air , leak testing, Instrument Loop check ,transmitters ,Indicators ,Analyzers ,local controller ,temperature gauge ,pressure gauge ,safety valve ,thermocouple , hand switch , pressure switch ,solenoid valve, control valve ,valve positioner , gas & smoke detectors, PSV & PRV, On-off valves installations, Non-displacer level etc.
Inspection Steam tracing on MANIFOLDS ,pressure insulated tube, vessels & pipes, material identification, receiving & storage , Pipe preparation, surface cleaning on location of installations, piping projections, thermo & angle of tubing ,steam tracer tubing piping & steam traps, steam tracing tubing & insulation, steam tracing panel (Tranter panel coils& Heat transfer compound)
E & I PUNCH List item checked & close out.
Pre-Commissioning & Commissioning with vendor site representative and project operations team for completed works/jobs, participated on all work down, functional check , test prior to energizing and start-up in substations, Skids & Modules, electrical panels, MCC & switchgears, Bar-bus units, Battery bank system etc.
-
DAEWOO E&C
- QAQC Supervisor E & I
2007 - 2008
Assignment for : SHELL PET, DEV, COMPANY
Project Name : INTERGRATED GAS TO POWER Project
Project Location : AFAM, NIGERIA
Business line : EPC & Pre-commissioning & Commissioning
Job Title : QAQC Supervisor E & I
RESPONSIBLE FOR : Constructions, Inspections, DOC System Turnover, Pre-comm. & Comm.
Brief Job Description (Onshore)
Preparation of all Quality control electrical & instrument sign off completed check sheets & turn-over to SPDC - Afam power site office.
Review of working procedure, ITP's & Quality forms for electrical and instrument activity with the Project Client.
Inspection of Electrical and Instrument materials, certifying them to be use on site.
Ensuring that all Electrical and Instrument devices & equipment's are installed according to the approved for construction drawing, (AFC).
Issuance of Non - Conformance Report to the construction where unauthorized deviation occurs.
Ensure that all Construction and Engineering activity are carried out according to SPDC Specifications and Standards.
Inspect and sign off all completed work with approved SPDC request for inspection sheets, checklist & ITP, with Approved for construction drawings.
Witness all cable inspection and test, eg: High-Potential (Hi-Pot) test, continuity check, Insulation resistance test before and after installation of cables - Power & Control cables.
MRI-Material receiving inspection of all E & I items for the projects installations.
Witness Site installation and acceptance test in areas like 330KV switchyard, Gas turbine Units.
Routine check on all site installations, punch for incomplete / unfinished installations & Notification for clearing of punch items.
Regular site daily, weekly and monthly meetings for the progress of the projects target.
Carry out quality control functions / activities of the projects or its parts, Including QC inspection schedules & collection of QC records; ensuring the availability quality records documents and implementation of quality plan on site.
Ensures, whenever necessary, the update of site QC Plans/Control Procedures, directing all deviations regarding the contract to the Project Quality Engineers/ Inspectors.
Inspections of installed earthing/grounding & lightening protection system, fire alarm & detection systems, communication Systems ,lighting installation ,panel and junction box installation ,Low & Medium voltage cable test ,underground & above ground cable installations .
Inspection of installed power Transformers and power lines with Switchgears, VT, CT, CB for the 3 Gas turbine units.
Inspection of Installed High Voltage Busbar & Conductors, LV & MV Cables, Switchgears ,MCC , HAVC Systems & other Mechanical/Electrical Operated Parts, Gas Turbine 1, 2, 3, Steam Turbine, 330KV Switchyard, Switchyard Control Equipment's, Natural Gas facilities as per Specifications, Standards & Approved Drawings.
Pre-Commissioning walk down to ascertain percentage mechanical completion of all Electrical & Instrument
-
DAEWOO E&C
- QAQC Supervisor E & I
2007 - 2008
Assignment for : SHELL PET, DEV, COMPANY
Project Name : INTERGRATED GAS TO POWER Project
Project Location : AFAM, NIGERIA
Business line : EPC & Pre-commissioning & Commissioning
Job Title : QAQC Supervisor E & I
RESPONSIBLE FOR : Constructions, Inspections, DOC System Turnover, Pre-comm. & Comm.
Brief Job Description (Onshore)
Preparation of all Quality control electrical & instrument sign off completed check sheets & turn-over to SPDC - Afam power site office.
Review of working procedure, ITP's & Quality forms for electrical and instrument activity with the Project Client.
Inspection of Electrical and Instrument materials, certifying them to be use on site.
Ensuring that all Electrical and Instrument devices & equipment's are installed according to the approved for construction drawing, (AFC).
Issuance of Non - Conformance Report to the construction where unauthorized deviation occurs.
Ensure that all Construction and Engineering activity are carried out according to SPDC Specifications and Standards.
Inspect and sign off all completed work with approved SPDC request for inspection sheets, checklist & ITP, with Approved for construction drawings.
Witness all cable inspection and test, eg: High-Potential (Hi-Pot) test, continuity check, Insulation resistance test before and after installation of cables - Power & Control cables.
MRI-Material receiving inspection of all E & I items for the projects installations.
Witness Site installation and acceptance test in areas like 330KV switchyard, Gas turbine Units.
Routine check on all site installations, punch for incomplete / unfinished installations & Notification for clearing of punch items.
Regular site daily, weekly and monthly meetings for the progress of the projects target.
Carry out quality control functions / activities of the projects or its parts, Including QC inspection schedules & collection of QC records; ensuring the availability quality records documents and implementation of quality plan on site.
Ensures, whenever necessary, the update of site QC Plans/Control Procedures, directing all deviations regarding the contract to the Project Quality Engineers/ Inspectors.
Inspections of installed earthing/grounding & lightening protection system, fire alarm & detection systems, communication Systems ,lighting installation ,panel and junction box installation ,Low & Medium voltage cable test ,underground & above ground cable installations .
Inspection of installed power Transformers and power lines with Switchgears, VT, CT, CB for the 3 Gas turbine units.
Inspection of Installed High Voltage Busbar & Conductors, LV & MV Cables, Switchgears ,MCC , HAVC Systems & other Mechanical/Electrical Operated Parts, Gas Turbine 1, 2, 3, Steam Turbine, 330KV Switchyard, Switchyard Control Equipment's, Natural Gas facilities as per Specifications, Standards & Approved Drawings.
Pre-Commissioning walk down to ascertain percentage mechanical completion of all Electrical & Instrument
-
DAEWOO E&C
- Site Engineer E& I
2006 - 2007
Assignment for : SHELL PET, DEV, COMPANY
Project Name : INTERGRATED GAS TO POWER Project
Project Location : AFAM, NIGERIA
Business line : EPC & Pre-commissioning & Commissioning
Job Title : E & I Site Engineer
RESPONSIBLE FOR : Construction Installations, Site Survey & Preparation, Pre-comm. & Comm.
Brief Job Description (Onshore)
Supervise, co-ordinate and manage all electrical, instrumentation installations performed on site with the required construction skill and professional abilities.
Supervise installation of switchyard deep underground earthing systems to Gantry towers and beams for the 330KV transmission systems.
Supervise the full installation of switchyard 10meters vertical underground cable tray installations.
Supervise the full installation of the switchyard transmission gantry, beam supports & towers for the 330KV transmission system.
Co-ordinate all supports re-fabrication at the E & I site workshop.
Supervise all galvanized & PVC conduit duct laying for the routing of cables underground till equipment location at the switchyard.
Supervise all installation of SF6 breakers, Current transformers, Voltage transformers, HV & LV Busbar & conductors, gantry and beam voltage accessories for transmission system.
Co-ordinate in the installation and test (Pre-commissioning) of cables to it equipment's.
Supervise the full installation of 3 power transformers (primary ~secondary connection) linking gas turbine 1, 2, 3.
Supervise installation of instruments & cables on the gas and steam turbines.
Supervise installation of New Switchgears, MCC, and HVAC Systems in the Electrical Control Rooms.
Supervise installations of cable ducts & cables, supports, cable trays, cabinets, electrical and control panels at the switchyard control room/building for transmission facilities.
Supervise installations of cable ducts & cables, supports, cable trays, cabinets, electrical and control panels at the main control room/building for gas & steam turbines.
Supervise full installation and test for MCB's, fire and gas system, fire alarm & detector system , lightening protection systems at the controls rooms.
Make & direct engineering updates of any modifications on site during installations to the engineering dept.
Report all construction related issues to the construction manager, hold meetings for the progress on the construction on site.
Make sure that drawings are AFC before using it to perform any task on site (P& ID, Wiring, schematic & installation details drawings, Vendor drawings, location drawings, hook-ups etc).
Lead development and implementation of project procurement, support engineering, construction planning for E & I activities.
Conduct site HSE & work related meetings with workings before commencement of daily activities.
Maintain all projects HSE requirements - PPE, Work permit, stop work culture if not safe and promote the use of HSE practices.
Co-ordinate the Pre-commissioning walk-down to ascertain percentage mechanical completion of all Electrical & Instrument activities on site.
-
DAEWOO E&C
- Site Engineer E& I
2006 - 2007
Assignment for : SHELL PET, DEV, COMPANY
Project Name : INTERGRATED GAS TO POWER Project
Project Location : AFAM, NIGERIA
Business line : EPC & Pre-commissioning & Commissioning
Job Title : E & I Site Engineer
RESPONSIBLE FOR : Construction Installations, Site Survey & Preparation, Pre-comm. & Comm.
Brief Job Description (Onshore)
Supervise, co-ordinate and manage all electrical, instrumentation installations performed on site with the required construction skill and professional abilities.
Supervise installation of switchyard deep underground earthing systems to Gantry towers and beams for the 330KV transmission systems.
Supervise the full installation of switchyard 10meters vertical underground cable tray installations.
Supervise the full installation of the switchyard transmission gantry, beam supports & towers for the 330KV transmission system.
Co-ordinate all supports re-fabrication at the E & I site workshop.
Supervise all galvanized & PVC conduit duct laying for the routing of cables underground till equipment location at the switchyard.
Supervise all installation of SF6 breakers, Current transformers, Voltage transformers, HV & LV Busbar & conductors, gantry and beam voltage accessories for transmission system.
Co-ordinate in the installation and test (Pre-commissioning) of cables to it equipment's.
Supervise the full installation of 3 power transformers (primary ~secondary connection) linking gas turbine 1, 2, 3.
Supervise installation of instruments & cables on the gas and steam turbines.
Supervise installation of New Switchgears, MCC, and HVAC Systems in the Electrical Control Rooms.
Supervise installations of cable ducts & cables, supports, cable trays, cabinets, electrical and control panels at the switchyard control room/building for transmission facilities.
Supervise installations of cable ducts & cables, supports, cable trays, cabinets, electrical and control panels at the main control room/building for gas & steam turbines.
Supervise full installation and test for MCB's, fire and gas system, fire alarm & detector system , lightening protection systems at the controls rooms.
Make & direct engineering updates of any modifications on site during installations to the engineering dept.
Report all construction related issues to the construction manager, hold meetings for the progress on the construction on site.
Make sure that drawings are AFC before using it to perform any task on site (P& ID, Wiring, schematic & installation details drawings, Vendor drawings, location drawings, hook-ups etc).
Lead development and implementation of project procurement, support engineering, construction planning for E & I activities.
Conduct site HSE & work related meetings with workings before commencement of daily activities.
Maintain all projects HSE requirements - PPE, Work permit, stop work culture if not safe and promote the use of HSE practices.
Co-ordinate the Pre-commissioning walk-down to ascertain percentage mechanical completion of all Electrical & Instrument activities on site.
-
NATIONAL ELECTRIC POWER AUTHORITY
- Electrical MTCE TECH 1
2000 - 2006
Assignment for : GENCO & TRANSYSCO
Plant Name : AFAM POWER STATION
Project Location : AFAM, NIGERIA
Business line : Power Transmission & Generation
Job Title : Electrical MTCE TECH 1
RESPONSIBLE FOR : Installations, Survey & Preparation, Protection Control & Metering, Testing.
Brief Job Description (Onshore)
Plan, monitor, co-ordinate and check maintenance activities and procedures together with line Maintenance Planner and Maintenance Manager.
Monitor electricity and utilities consumption (control room).
Power system maintenance and general service (power transmission facilities)
Installation of Transformers (Auxiliary& Power Transformers), Current Transformers, Voltage Transformer's & Circuit Breakers, Disconnecting Switch / Earthing Switch, Line Trap, Bus Bar Units , Insulators, Panels.
Fabrication, Coupling & Installation of Towers for 132KV, 330KV Beam Supports, Tower Structure for Power Conductor Lines of Different Voltages, Earthing & Lightning Protection System , Gantry Tower Supports for Current Transformer, Capacity Voltage Transformer, Circuit Breaker, Surge Arrestor, Support Isolator.
Installation, glanding and termination of power, control cables ,cable Tray , lightning & earthing protection installations
General maintenance & troubleshooting of transmitting equipment's (Controls, Protections and Metering) and faults in control ,protection & switchgears (Equipment's & Lines) ,system line circuit design, process & installation of 330KV, 132KV, 33KV, 11KV switchyard, distance transmission & distribution Lines.
Installation process of GT 11 & GT12 of Afam V - Isolation Phase Bus (IPB), Generator Circuit Breaker, Electric Motors, Excitation units.
General maintenance and overhauling of Electric Motors, Excitation Systems, MV and LV Bus Bars.
Routine inspection of the Circuit Breakers and other Switch Gears, Recycling / Replacement of Saturated Silica Gel ,Installation ,inspection & maintenance of 220V, 110V and 24V Battery Bank Systems.
Completed installation of an injection substation facilities ( CT ,VT , Isolators , mini -switchyard control room ) for Egberu/Afam community.
-
NATIONAL ELECTRIC POWER AUTHORITY
- Electrical MTCE TECH 1
2000 - 2006
Assignment for : GENCO & TRANSYSCO
Plant Name : AFAM POWER STATION
Project Location : AFAM, NIGERIA
Business line : Power Transmission & Generation
Job Title : Electrical MTCE TECH 1
RESPONSIBLE FOR : Installations, Survey & Preparation, Protection Control & Metering, Testing.
Brief Job Description (Onshore)
Plan, monitor, co-ordinate and check maintenance activities and procedures together with line Maintenance Planner and Maintenance Manager.
Monitor electricity and utilities consumption (control room).
Power system maintenance and general service (power transmission facilities)
Installation of Transformers (Auxiliary& Power Transformers), Current Transformers, Voltage Transformer's & Circuit Breakers, Disconnecting Switch / Earthing Switch, Line Trap, Bus Bar Units , Insulators, Panels.
Fabrication, Coupling & Installation of Towers for 132KV, 330KV Beam Supports, Tower Structure for Power Conductor Lines of Different Voltages, Earthing & Lightning Protection System , Gantry Tower Supports for Current Transformer, Capacity Voltage Transformer, Circuit Breaker, Surge Arrestor, Support Isolator.
Installation, glanding and termination of power, control cables ,cable Tray , lightning & earthing protection installations
General maintenance & troubleshooting of transmitting equipment's (Controls, Protections and Metering) and faults in control ,protection & switchgears (Equipment's & Lines) ,system line circuit design, process & installation of 330KV, 132KV, 33KV, 11KV switchyard, distance transmission & distribution Lines.
Installation process of GT 11 & GT12 of Afam V - Isolation Phase Bus (IPB), Generator Circuit Breaker, Electric Motors, Excitation units.
General maintenance and overhauling of Electric Motors, Excitation Systems, MV and LV Bus Bars.
Routine inspection of the Circuit Breakers and other Switch Gears, Recycling / Replacement of Saturated Silica Gel ,Installation ,inspection & maintenance of 220V, 110V and 24V Battery Bank Systems.
Completed installation of an injection substation facilities ( CT ,VT , Isolators , mini -switchyard control room ) for Egberu/Afam community.
