Jayanth Kumar MUNIRAMAPPA

En résumé

Entreprises

• Arts et Métiers ParisTech - Research Intern

  Paris 2017 - 2017 “Residual stress analysis of shot peened mechanical parts with complex geometries” under the supervision of Dr. Regis Kubler.
  
  Experimental:
  • Obtained residual stress profiles for shot peened Inconel 718DA by X - Ray Diffraction (XRD).
  • Study of effect of shot peening on the microstructure using SEM, ImageJ
  • Study of effect of shot blasting on the hardness of materials by indentation test.
  
  Design and simulation:
  • Design of 3D axisymmetric models by Abaqus.
  • Introduction of residual stress by python programming
  • Simulation of material removal and finding its correction by Abaqus.
  • Post-processing and analysis of results
  • Residual stress analysis with experimental data
  
  Software & Skills: Abaqus, XRD, SEM, ImageJ

• Safran Aircraft Engines - Research Project Member

  Courcouronnes 2016 - 2017 "Damage tolerance on Aero-structural component"
  
  • This research work was carried as part of academic project for Safran Aircraft Engines.
  
  • Implementing and evaluating the predictive capacities of tools based on the concepts of linear elastic mechanics of rupture in the case of aero-structure elements subjected to complex loadings.
  
  • The main objective is to define & realizing lifetime spectrum comparison with experimental data and develop a code to study this data. MATLAB is employed to develop code and an interface to obtain the data.
  • Single incremental method was used to determine fatigue failure of the component.
  
  
  Softwares used: AFGROW, MATLAB

• Institut PPRIME, CNRS UPR3346, ISAE-ENSMA, Université de Poitiers - Research Intern

  2016 - 2016 "Finite Element simulations of nanoindentation test on polymers" under supervision of Dr. Olga Smerdova.
  
  • Design of 2D axisymmetric Vickers pyramidal indenter penetrating the sample material.
  • Study of contact behavior and interaction properties for various material behaviors.
  • Performance analysis of contact behaviors.
  • Linear, nonlinear static behavior test.
  • Elastic, plastic and viscoplastic behavior test of the model.
  • Correlation of results with measurements.
  
  Software used: Abaqus
  

• Indian Institute of Science, Bengaluru - Research Intern

  2014 - 2014 Worked as the research assistant in the project, "studies on Production, Fabrication and Characterization of Open Cell Aluminum Foam Heat Exchangers" under the guidance of Dr. Satish Kailash and Prabha Agarwal from February 2014 to April 2014.
  • Design and analysis of heat exchanger by Catia V5, ANSYS
  • Demonstrated the new technique of fabrication process and tested for the effectiveness of heat exchange.
  • Initially the project was carried out as part of academics during the Bachelor's. Later, continued to work on the same project after graduation from July 2014 to September 2014.
  
  
  Software used: Catia V5, ANSYS

• Hindustan Aeronautics Limited - Intern

  2013 - 2013 Brief Study on the technical aspects and working of the `Mirage 2000' aircraft.

Formations

• ISAE-ENSMA (Ecole Nationale Supérieure De Mécanique Et D'Aérotechnique)

  Poitiers 2015 - 2017 Master of Science

• Visvesvaraya Technological University (Bangalore)

  Bangalore 2010 - 2014 Bachelor of Engineering
  
  Subjects: Aerodynamics, Aircraft Structures, Flight Stability and Control, Mechanical Vibrations, Dynamics of Machines, Propulsion, Mechanics of materials, Material Science and Metallurgy, Composites.

Réseau

• Harish KAREKYATHANAHALLI PRAKASH

• Ismail SABOUK

• Jerol SOIBAM

• Mahantesh NINGARADDY

• Pavithra SAMPATHKUMAR

• Shreman PARIKH