Menu

Khelifa TARIQ

Puteaux

En résumé

I Seeking a Quality inspector QC position in Oil & Gas Sector (On/Offshore) where I can expand on my experience in this field, and utilize to increase both customer satisfaction and the company's reputation
My education is Metallurgy Engineering, Experience in my study; I want to develop my abilities more in this area,
The challenging in my work is the solving problem Where i ’am trying very effort with my team


Mes compétences :
Ultrasonic Testing
Oil&Gaz
WQT
Welding
Liquid Penetrant Testing
Radiography Testiing
Magnectic Testing
Standard ASME-AWS-API-ASTM....
NDT
Corrosion
pipelines
Risk Analysis
Offshoring
ER prope
Failure Analysis
onshore
Assurance qualité
Metallurgy
NACE
EPC
Cathodic protection

Entreprises

  • Bureau Veritas - NDT Inspector ( Consultant)

    Puteaux 2013 - maintenant To undertake supervision, inspection and control on behalf of Company in the area of welding works and ensure that these works are implemented in accordance with the Project Integrated Basis of Design & all Project requirements Standards, code, procedures -Review of Welding Procedure Specification WPS, Repair Procedure, Weld Map, NDT Specifications –Inspection of Weld structures( CJP,T,K,Corner,Butt) by UT Flaw detection A-scan, MPI, DPI according AWS D1.1 2010 and API-RP-2X.
    - Planning RT, interpreting films according to API 1104, ASME B31.3 to Company PIPELINE GABON
    -Verify equipment calibration of NDT and welding and Materiel if according the specification and code
    -Prepare all NDE Reports as UT,PT,MT,RT -Coordinate with client representative on daily basis to resolve any quality problems or issues -Responsible of: Control welding , NDT activity , Quality Reports
    - Inspection of Offshore Structures as Buoyancy Tank, Spools Sea-Fastening-Module Table
  • South Ocean inspection Service - QC-Welding & NDT Inspector

    2012 - 2012 Visual for welding joints -Responsible of NDT activity such MT, PT(Visible& Fluor-escent) for Lifting Point and in surface of pumps equipment (Flange-Tee-Threads) -Coordinate the work with department of Stimulation, Cementation, Fraction to inspect the equipment according the procedure, Client specification -Responsible of Ultrasonic Thickness Measure UTTM of Piping (Pup Joint, Tee, Flange, Cross, Elbow, X Over, Steel Hose Chiksan Loop) and for Valves (Plug Valve, Safety Valve) -Handling tools inspection in Rig drilling (Manual and Auto tang-elevator-drill pipe) - Periodic Inspection of Lifting equipment (wire rope-slings-Lifting point-chain sling-hook) according Lifts Standard. -Inspect of Silo & Small Water tank by UT, VT
  • Jasem Construction Company - QC-Welding Inspector

    2011 - 2011 visual inspection of piping in CPF, Manifold -Continuation in the underground lines
    (Drainage) in CPF -Application NDT (VT-PT) and continuous NDE -Qualification test for the welder WQT according ASME IX. -Continuation the coating and painting - Preparation daily report of welding production, Welding book, WPQR, RFI and Preparing all NDT document -Preparation of requests and reports for the client and co-ordinate with client responsibilities -Preparation welding folder (Welding book, welding Map, WPQR, RFI ,Reports VT, PT, RT) -Responsible to Verify Fit-up, Fitting, Materials, Electrodes, Weld visual and Dimension
    -Inspected the Welding Operations like GMAW, SMAW & GTAW - Carried out repairs according to WPS. Prepare and maintain welding reports, rejection rate - Inspecting the weld joints before/during/after welding. Monitoring the welding parameters & inter pass temperature. Marking of welds on isometric drawings P&ID,
    -Recording of completed weld, -Responsible to check the method of Pre-heat applied prior to tack weld.
    Checked the flow rate of shielding and purging gases.
  • PETROJET - QC-Welding inspector

    2010 - 2011 Fabrication, Installation of 48” Material: API 5L X70 in 400 KM, for transportation & storage of Gas -Visual of joint Before/During/After Welding according WPS - Prepare Daily reports of production, Welding Book, Visual Reports –Assure of quality (Clearance, Dimensions, Hie-low, Weld) especially in Tie-in joints -Weekly reports to QA/QC Manger and Supervisor about: Quality of work, Production rate and deficiency
    Of Work -Welder’s Qualification Test WQT according the API 1104

Formations

  • NACE (Tunis / Tunisia)

    Tunis / Tunisia 2018 - 2021 NACE Corrosion technicien

    CORROSION
  • ABNDT (Chennai, Tamil Nadu, India)

    Chennai, Tamil Nadu, India 2014 - 2019 ASNT Level 2

    NDT UT RT PT MT
  • ABNDT (Chennai, Tamil Nadu, India)

    Chennai, Tamil Nadu, India 2014 - 2019 CSWIP 3.1

    Welding
  • Université Mohamed Khaidar Biskra (Biskra)

    Biskra 2006 - 2009 B.sc

    Metallurgy

Réseau