-
GoConcept
- Consulting Engineer
Nyon
2013 - maintenant
-
Johnson & Johnson
- Electronics and Embedded Medical Software Engineer
New Brunswick
2013 - 2014
1- Analysis and characterization of the power consumption of an implanted medical
device (battery analysis with manufacturer, hardware consumption in manufacturing
process).
2- Development of software for a medical monitor (bootloader, upgrade firmware
manager, pressure sensor measurement).
* Development language: C
* Micro Controller used: dsPIC ;
* Source level debug and test with MPLAB X (with ICD3). ;
* Integrate test and document software development. ;
* Design and code review.
* Participate to risk analysis
* Technical support for external contractor.
-
SAFRAN Group
- Electronics and Embedded Software Engineer
2012 - 2013
Hardware and software development for retrieving data from a helicopter calculator
system (for SAFRAN Group).
* Select the architecture of the system with SAFRAN's engineers.
* Design electronic schematics with ORCAD Capture for a prototype board around
an ARM AM3359 processor (NAND, SPI, CAN Bus, Ethernet).
* Creation of an embedded Linux OS for the system (U-Boot, Linux Kernel 3.2).
* Development of drivers for the board (SPI slave, timers).
-
Zodiac Company
- Electronics and Embedded Software Engineer
2011 - 2012
Hardware and software development of a device to pilot satellite antenna.
* Design electronic schematics with ORCAD Capture for a board around an ATOM
processor and a XILINX FPGA with Ethernet, USB, GPS, ADC, I2C, serial bus
and DVI.
* Write PCB Layout specifications.
* Write test procedure. ;
* Write VHDL module for managing CAN BUS, ADC and GPS. ;
* Technical lead of one engineer for coding activity. VHDL module for I2C, serial
bus and PCIe interface to communicate with the ATOM Processor.
-
Pekly Company
- Electronics and Embedded Software Engineer
2010 - 2010
Hardware and software development for a galvanometer with digital display for
helicopter.
* Design electronic schematics with ORCAD Capture for a board around a
PIC18F46J50 µC.
* Write the entire embedded software in C language to measure sensor and
display it both with the nail of the Galvanometer and on a digital display. Write the
code to manage the upgrade sequence with an USB interface.
* Design a human machine interface with Labwindows CVI to setup and upgrade
the system.
-
Cegelec Company
- Electronics and Embedded Software Engineer
2010 - 2010
Hardware and software development for a remote controlled stand for radiation sources
for an industrial radiography.
* Design electronic schematics with ORCAD Capture for a board around a
PIC18F46J50.
* Write the entire embedded software in C language to turn on a motor, to measure
the distance traveled by the radiation sources and display it on a LCD. Write the
code to manage the upgrade sequence with an USB interface.
* Design a human machine interface with Labwindows CVI to setup and upgrade
the system.
-
Supelec
- Electronics and Embedded Software Engineer
GIF-SUR-YVETTE
2008 - 2008
* Design electronic schematics with ORCAD Capture for an analog board with
band pass filter, ADC and a Xilinx FPGA.
-
SAFRAN Group
- Electronics and Embedded Software Engineer
2008 - 2010
Hardware and software development of a stand to pilot electrical linear motor for landing
gear aircraft.
* Selection of a power module board from microchip and modifying it to handle
more current (30A instead of 5A max)
* Design electronic schematics with ORCAD Capture for a board around a dsPIC
to pilot the power Module.
* Write the entire embedded software (C language) to pilot motor with speed and
current regulation.
-
IFREMER Company
- Electronics and Embedded Software Engineer
2008 - 2008
embedded software for a Human Machine Interface stand
* Write embedded software to manage RS232 bus (µC PIC, C language).
-
Thales Avionics
- Electronics and Embedded Software Engineer
2007 - 2008
Debug a test stand for avionic calculator
* Troubleshooting the system
* Replace some electronics components
-
Thales
- Electronics and Embedded Software Engineer
Courbevoie
2007 - 2007
electronic schematics with ORCAD Capture for a test stand according to
customer specifications
-
ERTE
- Electronics and Embedded software engineer
2007 - 2008
Hardware and software development of an optical sampling system technology at 40Ghz.
• Design electronic schematics with ORCAD Capture for a board around a HCS12 µC and optical components (Lasers, Mach Zender and Optical gate).
• Write the entire embedded software in C language to regulate laser current, Peltier Cells, Mach-Zender point regulation.
-
BOWEN ERTE
- Electronics and Embedded Software Engineer
2006 - 2013
Activities:
