Jean DUFOUR

En résumé

Entreprises

• SIAT - COO

  Louviers 2016 - 2017

• OCP group - Maintenance and Reliability Manager

  casablanca 2016 - 2016 • Completion all maintenance plans for the fertilizer plants (4x30 yo and 3x10 yo)
  • Preparation of starting of execution phase
  • Finalization of reliability process such as RCA, lubrication optimization,
  • Recruitment of engineers and technicians directly for TKIS and creating maintenance teams with subcontractors

• Albioma - EIA Project Manager Engineering

  PUTEAUX 2015 - 2016 * Revamping of DCS from ABB Modumat 8000 to Metso DNA and Emerson Ovation of power plants with coal/bagasse/biomass boilers in French DOM/TOM (Reunion and Guadeloupe islands).
  * 3 times 2 ``green'' boilers with 20 MW power generation ;

• glencore - Upgrading management

  2014 - 2015 for a global Zinc concentration plant and mine by flotation process (32 persons as local and expatriates engineers).
  From April 2015, engineering management responsibilities including heavy equipment garage added to actual
  * Oversight of budgeting, forecasting and business planning process ;
  * Development of cost reporting with area manager ;
  * Plant optimization by restarting of all control loops as plant-r was driven fully manually ;
  * Installation of optimization software Osisoft PI ;
  * Installation of CMMS
  * Upgrading local people technical training ;

• Vale - Maintenance and Reliability Manager

  Rio de Janeiro 2012 - 2014 Management maintenance and reliability for a nickel plant by hydrometallurgical process Seveso II classified (121persons): management of upgrade of SmartPlant and link with SAP R3
  * Crushing to feed plant
  * Hi pressure lixiviation
  * Chemical separation of Ni and Co
  * Sulphuric acid Plant with sulphur boiler ;
  * Power plant with 2x50 MW pulverized coal boilers and steam turbine ;
  * Overland conveyor (4 km)
  As maintenance manager, I was involved in every heavy operation of maintenance. I organized then followed each annual stop on each big machine, particularly power generators. All clearances and gaps were checked, MMS (Bently Nevada 3500) sensors was calibrated. Shafts and gearbox checked with oil analysis to see if any abrasion is present, alignments checked with laser sensors.

• Veolia Water - Project Manager

  Paris 2011 - 2012 Design management of Electricity/Instrumentation/System for an EPC project for a sludge incinerator plant: 2000 tpd of sludge coming from 11 waste water treatment plants: 23 persons
  Project composed of:
  * 4 kiln-boilers 32 t/h, 42 b
  * 2 steam turbines with 14 MW generator ;
  * Sea water treatment to produce process and drinkable water ;
  * Plant waste water treatment ;
  * All utilities as 4x 250 kW air compressors, 1x4 MW diesel generator ;
  * General management of studies ;

• Technip - Area Manager

  Paris 2007 - 2011 Management of multicultural team, for cost, detail design and planning: 48 persons
  * Area Lead Engineer for a Nickel plant in New Caledonia. Supervisor of various packages :
  * 2x150 MW CFB Boiler
  * 2x135 Steam Turbines
  * 2x50 MW Gas Turbines
  * Utilities ;
  * Approval of documents for those various packages ;
  * Contact with client an vendors to finalize the project
  * Erection, pre-commissioning and starting up of this area
  For pre commissioning I checked deeply all manufacturers procedures high pressure welding was analysed by  ray radiography. All alignment reports was checked and archived. Refractory drying then cooking was registered according to procedures. Bolts and gaskets was checked to install right quality at right place

• Veolia Water - Project Management

  Paris 2006 - 2007 multicultural team for cost, detail design and planning: 12 persons
  * Cost and planning management ;
  * Supervision of electricity and control studies. Approval and consulting for all motors, high power VFD, monitoring of all rotating machines.
  * Approval of all sensors and HART or Fieldbus networks on Delta V system, reviews with Vendor in Dubai
  * Definition of software sequences and process control ;
  * Design review, 3D model review with final client in Oman ;

Formations

• Ecole Nationale Supérieure De Physique ENSPM (maintenant EGIM)

  Marseille 1973 - 1978 Specialitees: electronique et techniques instrumentales

Réseau

• Abdesselem BOUCHERIT

• Aboubacar DISSAKI GAKOU

• Frederic REBIERE POUYADE (DE LA REBIERE DE LA POUYADE DE MONTGEOFFROY)

• Guillaume THEAU

• Jerome PENAUD

• José ARCOS

• Lahcen ELGHAZI

• Nebest COT

• Robert DULAS

• Tahre JENDOUBI